Metal sheeting candleholders

Say that title three times fast.

Did you just say it? Me too.

Oh yeah, it’s about that time! The kiddo will be out of school in a few short hours and after that it’s staying up late, sleeping in, eating cookies, watching movies and all kinds of general holiday debauchery. Cannot WAIT!

This is my last project working with True Value this year and it’s one I’ve been wanting to try for eons. Seriously, I’ve walked by these metal radiator grates for years and years and always wanted to do something with them. They’re just so pretty! There are so many designs to pick from too.

I picked up the cloverleaf design at my True Value for this project:

radiator grate candles

(For you locals I go to the Pendleton, IN location.)

I had two projects in mind and started with the easiest one. The other one will have to wait but I think it’s going to be awesome. :) This time I made some pretty candleholders with it and I think they turned out pretty cool!

You can see the design on the metal sheet better here:

radiator grate candles

This one is a pretty brass/gold color but there are other finishes available as well. Isn’t that cool?

I used tin snips to cut through it but scissors work too (it’s very thin):

radiator grate candles

It’s a good idea to wear some hand protection (even SpongeBob gloves would work) while cutting – the edges aren’t crazy sharp but you need to be careful with it.

By the way, I held my glass holders up to it to see what size to cut it first. Don’t forget that part. :) I used some extra Goodwill cylinders (just like I used for the Christmas mantel) – I told you I had a ton of these! They are ALWAYS at my local GW.

When it was cut out I rolled it up a bit so it would start taking the cylinder shape – you need to kind of help it along:

radiator metal candles

Then I wrapped it around the glass to see where the back met up. I took it off and then used a simple line of wire to secure the two together:

radiator metal candles I wrapped the wire at the bottom and the top of the metal to make sure it was going to stay put, and then just slid the metal “wrap” over the glass. That’s it!

I placed some simple votive holders with candles inside:

Radiator sheet candleholders

So pretty eh? I kept walking by them after I was done and oohing and ahhing to myself. They really are striking! I’m nuts over that metal design and the color. Of course you could spray paint the metal sheet any color you wanted too.

I think these look pretty for Christmas but they would work any time of year really:

Radiator grate candleholders

Couple of things – if you have little hands around you may want to add some ribbon around the top or bottom if you think kids will try to handle them. Like I said, the edges can be a bit sharp (it really depends on where you cut them).

Also, you really don’t need to have the glass candleholders! You could just as easily just roll them up, secure the back together and then place a votive holder inside – you can’t really tell there’s glass there when all is said and done.

And finally, this metal sheeting isn’t cheap – I think $20-something each? I’m not sure. But I got three good sized holders out of it and had plenty left over to make another, so it goes further than you think it will.

Have you tried any projects with this metal? I’m planning my next one already…I’ll let you know if it works out!

I’ll be taking most of the next week away to be with family – I’m sure I’ll be back before the holiday, but just in case I don’t “talk” to you before then – I hope you have a WONDERFUL holiday season. Stay safe and enjoy your family and friends!

 

I was one of the bloggers selected by True Value to work on the DIY Squad. I have been compensated for my time commitment to the program as well as writing about my experience. I have also been compensated for the materials needed for my DIY project. However, my opinions are entirely my own I would have done this project anyway and I have not been paid to publish positive comments.

Tidak ada komentar:

Posting Komentar